Athena C.5 Installationshandbuch Seite 132
- Seite / 181
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Series C Controller Configuration and Operation Manual
13-2 Athena Controls, Inc. 900M050U00
13.3 Menu Items
Parameter Name
: Calibration Low (see Note 1 below)
Name as Displayed
:
CALoCALo
Used By:
all
When Displayed:
always
Description:
Displays the temperature input value that should be simulated
during low calibration.
Beware! Pressing the or key while this is on display
will clear the controller’s existing zero offset and initiate the low
calibration, even if you have not prepared the controller as
described in Section 18. If the controller has not been prepared
correctly before you initiate calibration, the resulting calibration
will be invalid.
Parameter Name
: Calibration High (see Note 1 below)
Name as Displayed
:
CAHiCAHi
Used By:
all
When Displayed:
always
Description:
Displays the temperature input value that should be simulated
during high calibration.
Beware! Pressing the or key while this is on display
will clear the controller’s existing span adjustment and initiate the
high calibration, even if you have not prepared the controller as
described in Section 18. If the controller has not been prepared
correctly before you initiate calibration, the resulting calibration
will be invalid.
Note 1: The Athena Plus protocol does not permit you to read this value.
- Precautions 3
- Table of Contents 5
- 1. Introduction 13
- 1.1.2 What to Read 14
- 1.2.1 PID and On/Off Control 14
- 1.2.3 Alarm Annunciation 15
- 1.2.4 Ease of Configuration 15
- 1.2.5 Ramp/Soak Recipes 15
- 1.2.6 Serial Communications 16
- 1.3 Modes of Operation 17
- 1.3.2 Configuration 18
- Attention 18
- 1.4 Security 19
- 1.5 Control Types Supported 20
- 1.5.3 On/Off Control 21
- 8.2.2 for details 22
- 1.6 Setpoint 23
- 1.6.4 Second Setpoint 24
- 1.6.5 Remote Analog Setpoint 24
- 1.7 Alarm Annunciation 25
- 1.9.1 Outputs 29
- 1.9.2 Display 29
- 1.9.3 Setpoint 29
- 2. User Interface 31
- 2.2 Display 32
- ErrErr displayed 33
- 01000100 33
- 2.2.2 During Configuration 34
- 2.3 LEDs 36
- 2.3.2 On 1ZC Controller 37
- 2.4 Using the Keypad 38
- User Interface 39
- To clear all latched alarms: 45
- Instructions for PID Control 49
- 3.2 Quick Instructions 50
- 4. General Information About 55
- Configuration Parameters 55
- 4.3.1 Summary 57
- 4.5 Using Factory Defaults 62
- 5.1 Introduction 65
- Input Parameters 69
- 5.5.1 Parameter Used 70
- Input Types 73
- SP.HLSP.HL 74
- I.FILI.FIL 74
- SP.LLSP.LL 74
- Effect on Other 76
- 6.1 Introduction 79
- Used 82
- OFFOFF off 84
- 7.1 Introduction 85
- D1.A0D1.A0 86
- O1.ACO1.AC and O2.ACO2.AC 89
- O1.Cy O1.Cy and O2.Cy O2.Cy 90
- O1.LL O1.LL and O2.LLO2.LL 91
- O1.HLO1.HLand O2.HLO2.HL 92
- 1ZC and 16C Only 93
- O1.dLO1.dL and O2.dLO2.dL 95
- O1.IHO1.IH and O2.IHO2.IH 95
- O1.SP O1.SP and O2.SPO2.SP 96
- Are Used for Control 97
- See Note1 98
- See Note 2 98
- 8.2.1 Introduction 99
- 8.3.1 Introduction 101
- Control 102
- 9.1 Introduction 105
- and A2.A0A2.A0 108
- A1.dLA1.dL and A2.dLA2.dL 109
- A1.IHA1.IH and A2.IHA2.IH 109
- A1.SP A1.SP and A2.SPA2.SP 110
- Recommended 111
- Optional 113
- Ramp/Soak Recipe Parameters 115
- S.S.r.tS.S.r.t 117
- HLd.bHLd.b 117
- Ramp Time 118
- 11.4.1 Introduction 119
- Time in Minutes 120
- SL1SL1, SL2SL2 through SL8SL8 124
- 12.1 Introduction 127
- FS.01FS.01 and FS.O2FS.O2 128
- L.br.tL.br.t 128
- Since Last Reset 129
- Configuration 131
- 13.3 Menu Items 132
- 14.1 Introduction 133
- 14.2 Options Supported 133
- AlrAlr (alarm) menu 134
- AoutAout (auxiliary output) 134
- MODBUS 138
- Used 139
- Plus Protocol 140
- 14.7.1 Introduction 142
- 14.8.1 Introduction 143
- 14.9.1 Introduction 144
- Protocol 145
- all R/W See Note 2 151
- 16.1 Introduction 153
- 16.2 Autotuning 154
- 16.2.3 Autotune Error Codes 155
- (Zeigler-Nichols PID Method) 156
- 16.3.1 Introduction 156
- 16.3.2 Procedure 156
- 17.1 Introduction 159
- CnF9CnF9 160
- FACtFACt 160
- 17.2 Procedures 161
- 17.3 Disabling the Keypad 162
- 18.1 Introduction 163
- 18.2.1 Introduction 164
- FACtFACt (factory) 166
- 19. Error Messages and Codes 169
- 19.3 Problem with Controller 170
- 20.1 Introduction 173
- versa)? 173
- computer? 174
- controller! 175
- 21. Index 177
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern