Athena C.5 Installationshandbuch Seite 124
- Seite / 181
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Series C Controller Configuration and Operation Manual
11-12 Athena Controls, Inc. 900M050U00
11.4.3.3 Specifying the Setpoint for Each Soak in a Multi-Step Recipe
Parameter Name:
Soak Level 1, Soak Level 2 etc. through Soak Level 8
(58 though 65)
Name as Displayed
:
SL1SL1, SL2SL2 through SL8SL8
Used By:
all controllers
When Displayed:
if the recipe option is eight-segment r/s recipe
Range:
SPL.LSPL.L to SPH.LSPH.L (setpoint low limit to setpoint high limit from input
menu) (See Note 1 below.)
Default:
77
Description:
Used to specify the setpoint for the soak for each segment.
Each segment can use a unique soak level.
Effect on Other
Parameters:
No effect on other configuration parameters. Does affect the
setpoint used by the controller.
Note 1: The range is reduced if the value of the dSPLdSPL (display) menu dEC.PdEC.P (decimal
position) parameter is not 0 (zero). See 4.3.2 for more information about the effect of a
linear input on numerical ranges.
11.4.3.4 Specifying the Length of Each Soak in a Multi-Step Recipe
Parameter Name
: Soak Time 1, Soak Time 2 through Soak Time 8
(66 through 73)
Name as Displayed
:
St1St1, St2St2 through St8St8
Used By:
all controllers
When Displayed:
if the recipe option is eight-segment r/s recipe
Range:
0 to 9999 minutes
Default:
0
Description:
Used to specify the length of the soak time for each segment.
Each segment can use a unique soak time.
- Precautions 3
- Table of Contents 5
- 1. Introduction 13
- 1.1.2 What to Read 14
- 1.2.1 PID and On/Off Control 14
- 1.2.3 Alarm Annunciation 15
- 1.2.4 Ease of Configuration 15
- 1.2.5 Ramp/Soak Recipes 15
- 1.2.6 Serial Communications 16
- 1.3 Modes of Operation 17
- 1.3.2 Configuration 18
- Attention 18
- 1.4 Security 19
- 1.5 Control Types Supported 20
- 1.5.3 On/Off Control 21
- 8.2.2 for details 22
- 1.6 Setpoint 23
- 1.6.4 Second Setpoint 24
- 1.6.5 Remote Analog Setpoint 24
- 1.7 Alarm Annunciation 25
- 1.9.1 Outputs 29
- 1.9.2 Display 29
- 1.9.3 Setpoint 29
- 2. User Interface 31
- 2.2 Display 32
- ErrErr displayed 33
- 01000100 33
- 2.2.2 During Configuration 34
- 2.3 LEDs 36
- 2.3.2 On 1ZC Controller 37
- 2.4 Using the Keypad 38
- User Interface 39
- To clear all latched alarms: 45
- Instructions for PID Control 49
- 3.2 Quick Instructions 50
- 4. General Information About 55
- Configuration Parameters 55
- 4.3.1 Summary 57
- 4.5 Using Factory Defaults 62
- 5.1 Introduction 65
- Input Parameters 69
- 5.5.1 Parameter Used 70
- Input Types 73
- SP.HLSP.HL 74
- I.FILI.FIL 74
- SP.LLSP.LL 74
- Effect on Other 76
- 6.1 Introduction 79
- Used 82
- OFFOFF off 84
- 7.1 Introduction 85
- D1.A0D1.A0 86
- O1.ACO1.AC and O2.ACO2.AC 89
- O1.Cy O1.Cy and O2.Cy O2.Cy 90
- O1.LL O1.LL and O2.LLO2.LL 91
- O1.HLO1.HLand O2.HLO2.HL 92
- 1ZC and 16C Only 93
- O1.dLO1.dL and O2.dLO2.dL 95
- O1.IHO1.IH and O2.IHO2.IH 95
- O1.SP O1.SP and O2.SPO2.SP 96
- Are Used for Control 97
- See Note1 98
- See Note 2 98
- 8.2.1 Introduction 99
- 8.3.1 Introduction 101
- Control 102
- 9.1 Introduction 105
- and A2.A0A2.A0 108
- A1.dLA1.dL and A2.dLA2.dL 109
- A1.IHA1.IH and A2.IHA2.IH 109
- A1.SP A1.SP and A2.SPA2.SP 110
- Recommended 111
- Optional 113
- Ramp/Soak Recipe Parameters 115
- S.S.r.tS.S.r.t 117
- HLd.bHLd.b 117
- Ramp Time 118
- 11.4.1 Introduction 119
- Time in Minutes 120
- SL1SL1, SL2SL2 through SL8SL8 124
- 12.1 Introduction 127
- FS.01FS.01 and FS.O2FS.O2 128
- L.br.tL.br.t 128
- Since Last Reset 129
- Configuration 131
- 13.3 Menu Items 132
- 14.1 Introduction 133
- 14.2 Options Supported 133
- AlrAlr (alarm) menu 134
- AoutAout (auxiliary output) 134
- MODBUS 138
- Used 139
- Plus Protocol 140
- 14.7.1 Introduction 142
- 14.8.1 Introduction 143
- 14.9.1 Introduction 144
- Protocol 145
- all R/W See Note 2 151
- 16.1 Introduction 153
- 16.2 Autotuning 154
- 16.2.3 Autotune Error Codes 155
- (Zeigler-Nichols PID Method) 156
- 16.3.1 Introduction 156
- 16.3.2 Procedure 156
- 17.1 Introduction 159
- CnF9CnF9 160
- FACtFACt 160
- 17.2 Procedures 161
- 17.3 Disabling the Keypad 162
- 18.1 Introduction 163
- 18.2.1 Introduction 164
- FACtFACt (factory) 166
- 19. Error Messages and Codes 169
- 19.3 Problem with Controller 170
- 20.1 Introduction 173
- versa)? 173
- computer? 174
- controller! 175
- 21. Index 177
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern