Athena 6075 series Spezifikationen

SERIES6075TEMPERATURE CONTROLLERSWITH AUTO-TUNING PID ANDPLUG-IN COMPUTER INTERFACE

SECTION 3 OUTPUT MODULES3.1Module DescriptionThe Athena 6075 offers field interchangeable output modules. This uniquefeature makes it possible to fill

Standard ThermocouplesI.SA. TypeMaterialsColor CodeJIron-Constantant (I/C)White( + ) Red( - )KChromel-AlumelYellow( + ) Red( - )TCopper-ConstananBlue(

watchdog circuits and filtering built into the unit Contacts and coils must besuppressed! One very effective filter is a .1 ufd/600V capacitor in seri

SECTION 5 OPERATION5.1Front Panel FeaturesTouch Key and Indication Operation Layout1.2.3.4.5.6.7.Process Temperature or Parameter code is viewed on th

5.2Basic Series 6075 Setup1.The 6075 has dual-input ranges which allow selection of one of tworanges and T/C types, by simply moving the position of t

2. .Range of Adjustments (Parameters)All parameters are accessed by pressing the INDEX key. They are listedin the order they are displayed when th

Warranty LimitationsOther than those expressly stated herein,THERE ARE NO OTHERWARRANTIES OF ANY KIND, EXPRESS OR lMPLlED, AND SPECIFI-CALLY EXCLUDED

Locally Adjustable only (Not by Remote Keyboard)10 -At- Auto-Tune Damping 0=Low, 1 =normal,2=High11 -cF- Configuration 0 to15(See Note 4)12xx -ct-

pressed the INDEX key, the unit will advance to the High and LowCalibration positions. but index no further until the SETPOINTkey is depressed.CAUTION

SPECIAL NOTE:For Units utilizing only heating output, the cooling gain should beset by the user to the equivalent heat gain. The inverse is also true.

5.3Tuning the Controller5.3.1Introduction5.3.2The Series 6075 is a state-of-the-art automatic tuning PlD temperature con-troller. The user has the opt

5.3.2.20102Normal Damping - For processes that: (any combination of thefollowing)- have heaters that are properly sized.- have good coupling bet

STEP 6: When ready to start Auto-Tuning calculation of PlD settings pressthe “Enter/Tune” button. The displays will return to process andset point dis

4. Press STAND-BY again and temperature will begin to rise. When the pro-cess rises to the desired set point it will probably oscillate. Periodicallyd

SERIES 6075AUTO-TUNING PID TEMPERATURE CONTROLLERCONTENTS PAGESECTION 1 GENERAL INTRODUCTION . . . . . . . . . 11.1 General Des

SECTION 6 COMMUNICATIONS6.1 Communications ModulesOptional plug-in modules are available for the Series 6075 to allow interfac-ing to the most common

Standard and the 232 is the identification number for that particular Stan-dard. The C designates the last revision made to the RS232 standard. Thepur

SECTION 7 CALIBRATIONWARNING: These adjustments are factory set and should only be changed by aqualified person using calibrated equipment. Adjustment

SECTION 8 TROUBLESHOOTING8.1Troubleshooting - GeneralSymptomDisplay does not light up.Process display shows (- - -) or ‘HHHH’Probable Cause & Co

ATHENLAthena Controls, Inc. 5145 Campus Drive Plymouth Meeting, PA 19462Tel: (610) 828-2490 Fax: (610) 828-7084

SECTION 6 COMMUNICATIONS . . . . . . . . . . . 266.1 Communications Modules . . . . . . . . . . . .

GENERAL INTRODUCTIONSECTION 11.1General Description and CautionsAthena Controls, Inc. is proud of the Series 6075 which you will now use Ithas been m

SECTION 2 INSTALLATION INSTRUCTIONS2.1UnpackingUnpack the instrument and inspect for shipping damage. Report anydamage to the carrier immediitely.2.2